基于支持向量机的RSA电磁旁路分析方法

针对在旁路分析过程中由于噪声的影响，不能直接观察出RSA的加密过程这一问题，提出结合支持向量机的旁路分析方法，从分类的角度对RSA二进制模幂运算中的平方、乘法操作进行识别，根据密钥与操作的相关性，推断出RSA二进制密钥序列。基于此，对移动设备PCM-9589F凌动主板进行了RSA电磁旁路分析研究，使用串口通信技术实现了对目标设备CPU的旁路电磁信号的采集，并采用基于边界的单类支持向量机的方法，以分类的正确率为70%为阈值，实现了对RSA二进制模幂运算中平方、乘法操作的识别，提取了OpenSSL加密库中1?024位RSA加密算法的二进制密钥序列。相比于传统的简单分析方法，克服了因旁路信号质量低而无法破解密钥的难题。     

自然循环工况下离心泵阻力特性的实验研究与数值模拟

停转后泵的阻力特性对自然循环流量影响明显。为研究低流量自然循环工况下离心泵的阻力特性，设计了实验台架，对离心泵的正向压降、反向压降和损失系数进行了测量，实验雷诺数为2.0×10⁴～1.5×10⁵。实验表明：相同雷诺数下，反向压降明显高于正向压降；雷诺数大于8×10⁴时，损失系数基本保持不变，而低雷诺数下损失系数随雷诺数的降低有增大的趋势；基于实验得到了损失系数的经验关系式。采用CFD方法对离心泵的内部流场进行了模拟，计算表明：CFD方法能较好地预测损失系数，RNG k-ε模型与实验值的相对误差不超过10%；离心泵的压力损失主要集中在叶轮、导叶等结构的交界区域；正向与反向流动的流场分布存在显著区别；低雷诺数下局部流动更加不稳定。     

Corrosion protection of aluminum alloy by epoxy coatings containing polyaniline modified graphene additives

In the study, polyaniline/reduced‐graphene oxide (PANI‐RGO) composites, fabricated by loading 2, 5, and 8wt% graphene oxide, was prepared by in‐situ emulsion polymerization and reduction. They are characterized by Fourier transform infrared spectroscopy, X‐ray diffraction, and scanning electron microscopy. Epoxy coatings adding PANI and PANI‐RGO composites were coated on the surface of AA5083 Al alloy. The anticorrosion performance of the coatings is measured by electrochemical impedance spectroscopy and potentiodynamic polarization curve in 3.5wt% NaCl solution. The results demonstrate that the epoxy/PANI‐RGO coating exhibits a better protection against AA5083 alloy corrosion compared with the epoxy/PANI coating. Enhancement of the passivation performance of PANI was obtained by the addition of RGO into epoxy/PANI coating system.     

Theoretical and Experimental Studies for the Transient Response of Cavity

During the transient state of aero-engine,cavity has evidently transient characteristics in the secondary air system.To investigate transient characteristics,theoretical and experimental studies were implemented for both static and rotating cavities.First of all,the typical transient response phenomena in secondary air system were investigated based on the basic concepts of the dynamic process.According to the basic theory of gas dynamics,the causes of transient phenomena were analyzed in two aspects,external disturbance,and system physical properties.Several dimensionless parameters were introduced to analyze the transient response characteristics of air system.Second,the experimental results of the static cavity indicated that the actual response time increased with the increase of the inlet pressure.The experimental results of the rotor-stator cavity showed that the low rotational speed on the response process had little effect,and the response time gradually increased when the speed continued to increase.Third,the test results of multiple components suggested that when the valve was opening the inlet pressure of the static cavity increased quickly and then reached a stable value,but the pressure of the static cavity,stable pressure cavity and rotor-stator chamber rose gradually.It was also obtained the actual response time of them was increased.The closer the measuring points were to the disturbance source,the shorter the delay time was.     

水热处理过程中伊敏褐煤微观结构的演变规律

褐煤水热处理可以脱除有害元素,降低n(O)/n(C)比,提高煤阶,有利于煤的洁净利用。利用高压反应釜对褐煤进行水热处理,采用拉曼光谱(Raman)和傅立叶红外光谱(FTIR)对处理后的煤样的化学结构进行分析,探索了不同温度水热处理后煤样微观结构的演变规律。结果表明:150℃水热处理时部分含氧官能团脱除,同时,部分脂肪族侧链断裂及不稳定大分子芳环结构分解形成小分子芳环结构,部分CO分解形成各类醚和羟基;当水热温度升至200℃,处理后褐煤的芳香度指数(R)和芳香结构稠合指数(DOC)上升,表明煤内缩合结构增加,同时,缺陷结构和杂环被去除,大分子芳环结构相对增加,CO大量分解;水热温度继续升高至250℃,褐煤发生氢转移反应导致脂肪族侧链增加;当水热温度达到300℃时,褐煤的芳环结构被破坏,交联结构和无定形碳增加。     

ZIF衍生多孔碳纳米纤维用于高效电容去离子的研究

作为一种环保节能的新兴脱盐技术，电容去离子技术正在成为替代反渗透脱盐和电渗析脱盐的一项重要的脱盐技术。各种碳基材料被广泛地应用于电容去离子电极材料的研究，然而大多数碳基材料为粉末状材料，需要添加黏结剂，这必将导致电极材料电吸附能力的下降。利用静电纺丝技术，将ZIF纳米颗粒和聚丙烯腈混纺，并通过分段高温热处理过程，成功合成了具有柔性结构的整体性多孔碳纳米纤维。由于其具有孔道结构的分级分布和较强的亲水性等优良特性，所制得的多孔碳纳米纤维在1.2 V电压下于500 mg/L NaCl溶液中表现出良好的电吸附性能，脱盐量达到了19.92 mg/g，比普通碳纳米纤维提高了一倍以上。     

核电厂聚乙烯管道设计方法及标准简介

随着聚乙烯管道在三门核电厂、大亚湾核电厂中的试应用成功，大量的新建核电厂及核电厂改造项目均将聚乙烯管道作为海水冷却水管道系统的首选管材，自主研制核电厂聚乙烯管技术标准迫在眉睫。本文介绍了核电聚乙烯管道的发展历史和应用现状，对比了核安全3级聚乙烯管道和非核安全相关聚乙烯管道、城市燃气与给水聚乙烯管道技术标准的设计方法及适用范围，探讨了中国目前聚乙烯管技术标准与核3级聚乙烯管道技术标准的差异与差距，为核电厂聚乙烯管道的设计制造与标准研制提供参考。     

提高Mn系低温脱硝催化剂抗硫抗水性能的国内外研究概述

介绍了氮氧化物的来源、SCR脱硝的反应机理和工艺流程、催化剂的硫和水中毒机理,重点介绍了国内外学术和工业界为提高催化剂抗硫和抗水性能所做的研究和尝试,旨在推动低温SCR技术的进展,促进该技术早日实现在工业上的大规模应用。     

C8 BTBT薄膜结晶形貌及OTFT器件性能研究

以p型共轭有机小分子2,7二辛基[1]苯并噻吩并[3,2‐b]苯并噻吩(C8‐BTBT)作为底栅顶接触有机薄膜晶体管(OTFT)的有源层,采用浸渍提拉法、喷墨打印法和真空蒸镀法三种制备工艺,探究半导体薄膜载流子迁移率与结晶形貌的关系,发现不同工艺下有机小分子呈现出不同的生长行为和结晶情况,在很大程度上决定了OTFT器件性能的优劣;此外,通过XRD分析研究了退火处理对C8‐BTBT结晶的影响。结果表明,真空蒸镀制备的薄膜具有更高的结晶度、衬底覆盖率高,并且呈现出SK(Stranski‐Krastanov)模式的结晶生长特征,相应器件中陷阱密度最低,迁移率高达5.44 cm^2·V^-1·s^-1,开关比超过106;且退火处理会严重破坏C8‐BTBT薄膜的结晶。因此,控制半导体层的生长行为,提升半导体层的覆盖率和结晶度是制备高性能共轭小分子OTFT器件的有效途径。